Teejet Matrix Pro 840GS User Manual Page 54
- Page / 82
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
48
www.teejet.com
HOMEOVERVIEW SETUP IMPLEMENT FULL SCREEN GPSINTRODUCTION GUIDANCE DROPLET MONITOR
SmartCable or Section Driver Module
If a SmartCable or Section Driver Module (SDM) is present,
BoomPilot is used to set automatic section control to off/
manual , automatic or all on .
NOTE: If a SmartCable or Section Driver Module (SDM) is not
present, please refer to Single section to view example.
GPS is unavailable when the BOOMPILOT icon
is grey . BoomPilot status bar icon will be off/
manual .
Figure 6-41: Automatic to all sections on mode
7.2
km/h
2.07
ha
> 0.0 <
A
A
Console only
To switch BoomPilot to automatic :
1. Press NAVIGATION AND GUIDANCE OPTIONS tab to
display navigation options.
2. Press BOOMPILOT icon .
◄Automatic – status bar icon will change to green
In areas where application is not desired:
1. Press NAVIGATION AND GUIDANCE OPTIONS tab to
display navigation options.
2. Press BOOMPILOT icon .
◄Off/manual – status bar icon will change to red
Press the BOOMPILOT icon again to resume application.
To turn all sections on :
1. Press NAVIGATION AND GUIDANCE OPTIONS tab to
display navigation options.
2. Press and hold BOOMPILOT icon .
◄All On – Status Bar Icon will change to yellow
Matrix Pro GS Boompilot Switch Configuration
BoomPilot
(ABSC) System
Rate Controller RC with Internal SDM
Work Switch
Spray
IconMaster Boom Switches Master Boom Switches
Automatic Mode On Off On On Off
Manual Mode On On On On Off
Rate controller or Switchbox
To switch BoomPilot between off/manual and automatic
when a rate controller or switchbox in on the system:
1. Turn the rate controller master switch to the “On” position.
The individual boom section switches should remain in the
“Off” position.
2. Press NAVIGATION AND GUIDANCE OPTIONS tab
to
display navigation options.
3. Press BOOMPILOT icon
.
◄Automatic – status bar icon will change to green
In areas where application is not desired:
1. Press NAVIGATION AND GUIDANCE OPTIONS tab to
display navigation options.
2. Press BOOMPILOT icon .
◄Off/manual – status bar icon will change to red
Press the BOOMPILOT icon again to resume application.
OR
1. Manually turn “off” the rate controller master switch to shut off
the booms.
◄Off/manual – status bar icon will change to red
Turn the master switch “on” to resume application.
To turn all sections on :
1. Press NAVIGATION AND GUIDANCE OPTIONS tab to
display navigation options.
2. Press and hold BOOMPILOT icon .
◄All On – status bar icon will change to yellow
Rate controller with Internal Section Driver Module
When using a rate controller with an internal section driver
module, both the master switch and the boom section switches
need to be in the “On” position..
Work on/off switch
When installed, work on/off switch should remain in the “off”
position for all setup options.
- MATRIX PRO GS 1
- Table of contents 3
- CHAPTER 6 GUIDANCE 30 4
- CHAPTER 7 GPS 52 5
- Safety information 6
- CHAPTER 1 SYSTEM OVERVIEW 7
- Matrix Pro 840GS console 8
- RealView® camera 8
- Additional information 8
- CONFIGURATIONS 9
- > 0.0 < 10
- Console screen colours 11
- Simple or Advanced mode 11
- Antenna to boom (m) 12
- Simple mode 14
- Advanced mode 14
- 98-05273-EN R4 15
- CHAPTER 5 SYSTEM SETUP 17
- CONFIGURATION 18
- Implement 19
- Implement 20
- Lightbar 21
- AutoSteer 21
- Tilt correction 22
- PRN not shown 23
- Video setup unavailable 23
- Sensors unavailable 24
- Pressure Sensor 24
- Droplet size monitor 25
- DATA MANAGEMENT 26
- Job data 26
- Transfer 27
- Reports 28
- Options 28
- Machine settings 29
- Machine settings availability 31
- CONSOLE 32
- Cultural 33
- Audio volume 33
- Demo mode 34
- CHAPTER 6 GUIDANCE 36
- Navigation screens options 37
- GUIDANCE BAR 38
- STATUS BAR 39
- Status/information screens 39
- GUIDELINES 46
- Curved lookahead guideline 46
- Marking A and B points 46
- Enter name 47
- Guideline name: Stream Edge 48
- Total number of guidelines: 4 48
- Turn now 49
- APPLICATION BOUNDARY 50
- Area bounded = 64.45 ha 51
- Save Delete 51
- RETURN TO POINT 52
- BOOMPILOT 53
- Single section 53
- CHAPTER 7 GPS 58
- GPS type 59
- GPS port 59
- GPS status information 59
- GGA requirements 60
- Programming receiver 60
- Alternate PRN 61
- CHAPTER 8 IMPLEMENT SETUP 62
- SINGLE SECTION SETUP 64
- – used to enter the offset 65
- OEM spreader implement type 66
- Straight implement type 68
- Staggered implement type 70
- – used to enter the 70
- FACTORY SETTINGS & RANGES 74
- Backwards 75
- 0.0 m -75.0 to 75.0 m 75
- Low pressure alarm (bar) 76
- + 78
- AIXR TeeJet® AIXR11004 79
- Very coarse 79
- 0 1 2 3 4 5 6 7 bar 79
- Unit specications 81
- Copyrights 81
- Trademarks 81
- Limitation of liability 81
Related products and manuals for Computers Teejet Matrix Pro 840GS
(82 pages)
(82 pages)
(82 pages)
(82 pages)
Computers Teejet CenterLine 2.0 User Manual
(66 pages)
(66 pages)
Computers Teejet Swath XL User Manual
(162 pages)
(162 pages)
© 2020, manymanuals.com. All rights reserved. | 0.238 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals