Teejet Matrix Pro 840GS User Manual Page 21
- Page / 82
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
15
98-05273-EN R4
HOME OVERVIEWSETUP IMPLEMENT FULL SCREENGPS INTRODUCTIONGUIDANCEDROPLET MONITOR
Lightbar
Lightbar setup is used to congure LED brightness, display mode
and LED spacing.
1. Press CONFIGURATION side tab .
2. Press
Lightbar .
3. Select from:
►LED brightness – used to adjust the brightness of the LEDs
►Display mode – used to determine whether the lightbar
represents the swath or vehicle. When set to "swath", the
LEDs represent guideline location and the moving LED
represents the vehicle. When set to "vehicle", the centre
LED represents vehicle location and the moving LED
represents the guideline.
►LED spacing – used to set the distance away from the
guideline or vehicle each illuminated LED represents
4. Press RETURN arrow or CONFIGURATION side tab
to return to the main Conguration screen.
Figure 5-9: Lightbar
AutoSteer
When a Steering Control Module (SCM) is present, assisted/auto
steering options will be available. For detailed setup instructions,
refer to your specic assisted/auto steering installation manual.
NOTE: An update of your SCM software may be required when
upgrading to a Matrix Pro GS from previous Matrix
systems. To view version of software information, see the
Console->About screen.
AutoSteer setup is used to enable/disable assisted/auto steering
and congure valve setup, steering settings, valve test, valve
diagnostics and steering angle sensor.
1. Press CONFIGURATION side tab .
2. Press
AutoSteer .
3. Select if assisted/auto steering is enabled or disabled.
4. When enabled, select from:
►Valve setup – used to congure valve type, valve frequency,
minimum duty cycle left/right and maximum duty cycle
►Steering settings – used to establish coarse steering
adjustment, ne steering adjustment, deadband and
lookahead
►Valve test – used to verify if steering is directed correctly
►Valve diagnostics – used to test the valves to see if they are
connected properly
►Options: Steering wheel sensor – used to select whether
the steering disengage sensor is magnetic or pressure
sensor based
►Steering angle sensor – used to establish and calibrate
the Steering Angle Sensor (SAS) as the primary feedback
sensor for auto steering.
5. Press RETURN arrow
or CONFIGURATION side tab
to return to the main Conguration screen.
Figure 5-10: AutoSteer
- MATRIX PRO GS 1
- Table of contents 3
- CHAPTER 6 GUIDANCE 30 4
- CHAPTER 7 GPS 52 5
- Safety information 6
- CHAPTER 1 SYSTEM OVERVIEW 7
- Matrix Pro 840GS console 8
- RealView® camera 8
- Additional information 8
- CONFIGURATIONS 9
- > 0.0 < 10
- Console screen colours 11
- Simple or Advanced mode 11
- Antenna to boom (m) 12
- Simple mode 14
- Advanced mode 14
- 98-05273-EN R4 15
- CHAPTER 5 SYSTEM SETUP 17
- CONFIGURATION 18
- Implement 19
- Implement 20
- Lightbar 21
- AutoSteer 21
- Tilt correction 22
- PRN not shown 23
- Video setup unavailable 23
- Sensors unavailable 24
- Pressure Sensor 24
- Droplet size monitor 25
- DATA MANAGEMENT 26
- Job data 26
- Transfer 27
- Reports 28
- Options 28
- Machine settings 29
- Machine settings availability 31
- CONSOLE 32
- Cultural 33
- Audio volume 33
- Demo mode 34
- CHAPTER 6 GUIDANCE 36
- Navigation screens options 37
- GUIDANCE BAR 38
- STATUS BAR 39
- Status/information screens 39
- GUIDELINES 46
- Curved lookahead guideline 46
- Marking A and B points 46
- Enter name 47
- Guideline name: Stream Edge 48
- Total number of guidelines: 4 48
- Turn now 49
- APPLICATION BOUNDARY 50
- Area bounded = 64.45 ha 51
- Save Delete 51
- RETURN TO POINT 52
- BOOMPILOT 53
- Single section 53
- CHAPTER 7 GPS 58
- GPS type 59
- GPS port 59
- GPS status information 59
- GGA requirements 60
- Programming receiver 60
- Alternate PRN 61
- CHAPTER 8 IMPLEMENT SETUP 62
- SINGLE SECTION SETUP 64
- – used to enter the offset 65
- OEM spreader implement type 66
- Straight implement type 68
- Staggered implement type 70
- – used to enter the 70
- FACTORY SETTINGS & RANGES 74
- Backwards 75
- 0.0 m -75.0 to 75.0 m 75
- Low pressure alarm (bar) 76
- + 78
- AIXR TeeJet® AIXR11004 79
- Very coarse 79
- 0 1 2 3 4 5 6 7 bar 79
- Unit specications 81
- Copyrights 81
- Trademarks 81
- Limitation of liability 81
Related products and manuals for Computers Teejet Matrix Pro 840GS
(82 pages)
(82 pages)
(82 pages)
(82 pages)
Computers Teejet CenterLine 2.0 User Manual
(66 pages)
(66 pages)
Computers Teejet Swath XL User Manual
(162 pages)
(162 pages)
© 2020, manymanuals.com. All rights reserved. | 0.073 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals